ProSim SA
Immeuble Stratège A
51, rue Ampère
F-31670 Labège

Tel. :+33 (0)5 62 88 24 30
Fax :+33 (0)5 62 88 24 39

ProSim Inc
325 Chestnut Street
Suite 800
Philadelphia, PA 19106

Tel. :+1 215 600 3760
Fax :

  • We make sure to deliver a Premium Support and knowledge for you to realize the full potential and functionalities of your software. Our customers are our Priority!

Advanced process simulation and energy efficiency analysis with ProSimPlus

May 19-20, 2020 LEVEL 2
  • ProSimPlus
  • Simulis Pinch
ProSim SA - Labège (31)
Language: English
COST 990.00 € + Tax

This level 2 training course will enable participants to master the principles of continuous steady state processes simulation and modeling. Trainees will study issues related to physico-chemical properties, unit operation modeling, mass-energy balances and numerical aspects.

At the end of the course, the participants will be able to:

• Quantify the energy performances of the processes and optimize them,
• Use pinch technology to compare consumption of utilities with theoretical minima (carry out an energy diagnosis),
combine the energy analysis of a process and the production of associated utilities all without leaving the process simulator
• Design efficient heat exchanger networks
• Install equipment to improve the energy efficiency of processes: Heat pump, ORC, Methanisation, Fuel turbine, Boiler ...
• Evaluate the proposed solutions from an economic point of view

Participants will have an advanced experience in both the use of the ProSimPlus software for energy, exergy and economical evaluation of their process, and also will be proficient with the use of Simulis Pinch software for the design of energy efficient heat exchanger network.

Who should attend?
This training session is designed for engineers involved in conception, optimization and energy efficiency analysis of processes and for those in charge of the efficiency of an installation running under different operating conditions. This session is also very relevant for the energy managers, energy auditors, eco-efficient facilities designers, and all other engineers responsible to solve these important challenges.


Day one: 9:00 am - 6:30 pm

I  Introduction:  
   -  Overview about ProSimPlus
   -  Main functionalities under ProSimPlus

II  Pinch module:
   - Pinch methodology
   - Pinch module for energy diagnostic in ProSimPlus

III Simulis Pinch:
   - Software introduction
   - Heat exchanger network synthesis (theory and practice)

Day two:  9:00 am - 6:00 pm

IV  Exergy module:
   - Exergy: theory and concept
   - Exergy analysis of a process
   - Exergy module in ProSimPlus

V  Specific unit operations for energy efficiency:
   - Thermodynamic cycles: heat pump, generalized heat pump, ORC...
   - Energy production: combustion, boiler, fuel turbine, fuel engine...
   - Waste treatment: methanization reactor,...

VI  Economic evaluation module:
   - Theory
   - Use of the module in ProSimPlus


Cost and Conditions
LEVEL 2 training courses are not included in the MUTS Services (Maintenance, Update, Training and Support) contract. The cost of this training session is 990 Euros (Exc VAT) per person.
It includes the training participation, lunch, refreshments and documentation. Other travel and accommodation costs are not included.
A 290 Euros fee will be charged for cancellations within last week before session date.

As the number of participants is limited, please register at least 10 days before the training session.

ProSim reserves the right to cancel a course if there are not enough participants.

Training organization
Duration: two consecutive days
Location: ProSim training room, at Labege / France (see Access map)
Accommodation: some useful addresses here
Hardware and software: The required hardware and software are provided by ProSim, with, in general, one computer for two trainees in order to facilitate exchanges between participants.
Approach: The training course includes theoretical parts and applications exercises. A number of concrete case studies are discussed.
Software to be used : ProSimPlus and Simulis Pinch

Level 1 course: steady state processes modeling and simulation
Background in chemical engineering / process engineering
Knowledge in thermodynamics
Basic knowledge in software utilization in windows environment

Additional relevant training
Thermodynamic approach in process simulation (suggested prerequisite)
Advanced stead-state processes modeling and simulation